The Roadmaster Rear Anti-Sway Bar # RM-1139-173 contains the polyurethane bushings and mounting hardware to install onto your 2017 Ford F-250. The only extra item you would need is the end link kit. The sway bar and end link kit is available in one package, the Roadmaster Rear Anti-Sway Bar and End Link Kit
# RM-1139-173-00.
This kit will be everything you need to install the rear anti-sway bar on your 2017 Ford F-250. view full answer...
Yes, the bushing brackets are included with the Roadmaster Front Anti-Sway Bar and Bushing Kit # RM-1109-116. I have included a picture that outlines what parts are included for you to check out. view full answer...
The Roadmaster Front Anti-Sway Bar # RM72MR is only going to come with two 5/8" shackle bolts for the end links and would require you to reuse the factory M14 bolts and clamps that should've been on your motorhome. If they truly are not there you would need to get in contact with REV Group, Inc. (the manufacturer) to determine what the length of the 5/8" bolts need to be or you could get some that are a few inches in length and cut them down as needed and get the some locking flange nuts... view full answer...
Yes, the Thule Passage 2 Bike Carrier - Trunk Mount Item # TH910XT does have anti-sway cradles. There may have been a much older version that did not and that is why there is conflicting information. But the Passage does for a fact have anti-sway cradles. It is also a fit for your 2002 Toyota Solara Convertible.
If you will be carrying womens, childrens, or alternative frame bikes, I recommend adding the bike adapter bar, # 64005, in order to carry the bikes more level. I have included... view full answer...
Thank you for the questions about the Roadmaster Rear Anti-Sway Bar and End Link Kit # RM-1139-173-00 for your 2015 Ford F-350 Super Duty.
I spoke with my contact at Roadmaster who wasn't sure why they don't have specific instructions for the end link kit but he did say that you just connect the links to the sway bar and then lift them up to holes in the frame which allow them to hang straight down.
This kit is comprised of 2 different kits; the sway bar kit # RM-1139-173 and the End... view full answer...
The Roadmaster Polyurethane Bushing Kit for 1-1/2-Inch Diameter Factory Rear Anti-Sway Bar, part # RM-4139-125, includes two polyurethane bushings, steel U-shaped brackets plus a bag of installation hardware.
If you refer to the linked photo that shows a complete sway bar kit you will see two arrows indicating a pair of bushings with the steel U-brackets. Two of these are included in the replacement kit along with the bushings and hardware. view full answer...
Yes, the weld on sway control ball mount tab is included with the Reese sway control, part # 83660.
We also carry weld on sway control tabs separately, part # 3442, see link. view full answer...
Yes, the 4 Bike Rack for 2 Trailer Hitches, Wheel Mount - Swagman XTC4, part # S64665, comes with an anti-rattle hitch pin, but this is not a lock. The Locking Anti-Rattle, Threaded Hitch Pin for Swagman 2 inch Hitch Racks is part # S64027. view full answer...
The Replacement SuperCush Anti-Sway Cradle and ZipStrips part # 8880598 is just for one side, you'd need the other side as well to secure the bike, the Replacement SuperCush Cradle and ZipStrip for Yakima Hanging-Style Bike Racks part # 8880597. In other words, there are two cradles per bike and the part number you referenced is only one cradle.
If you have one of the bike racks listed on the product page then you don't need to worry about verifying dimensions. view full answer...
The Rola NV2 bike rack comes with hitch pins for the 1-1/4 inch and 2 inch shank ends on the bike rack but does not have an anti-rattle threaded bolt. If you are using the 2 inch end, you can use the anti-rattle and hitch lock # SR25219.
If you are using the 1-1/4 inch end, since it is solid, you can use # 63090 for the anti rattle and the # 2848DAT for a hitch lock. I have included a link to a video review of the bike rack for you and a link to a video on the anti-rattle device. view full answer...
If you wanted to order the Curt Shock Absorbing Towing Starter Kit pat # C57DR without the brake controller you'd just need to order the individual components of the kit without the controller. So what you'd want would be the Rocker Ball # C45WR, the sway control part # 17200 and the Curt anti-rattle kit part # C22321. view full answer...
The part # RM-590064-00 is a part that is normally used with a sway bar kit # RM-1209-128 on Sprinter vans that don't have a factory sway bar. The sway bar part number does come with the needed bushings to use with the adapter. view full answer...
The Replacement Bushing # RM-205219-10 is only 1 bushing for your Roadmaster 1-3/8" round sway bar. I always recommend replacing the bushings as a set on a sway bar. view full answer...
The replacement Pro Series weight distribution head # PS58442 does come with the hitch ball, sway control ball, and all necessary mounting hardware.Basically everything you see in the pictures.
This head is a replacement for Pro Series weight distribution systems # PS49583, # PS49582, and # PS49901. view full answer...
You mentioned that you do not have a hitch, but there is a very good retractable trunk-mounted rack option for your 2010 Ford Escape Hybrid.
I recommend going with the Thule OutWay 3-Bike Rack, # TH56BV, which has anti-sway cradles that secure your bikes at three points, No-Sway cages which prevent the bikes from contacting each other or your Escape, and a weight capacity of 99 lbs. The OutWay also has 2 retractable cables to secure the rack to your car, with ratcheting knobs to adjust... view full answer...
The Reese Dual Cam High-Performance Sway Control, part # RP26002 has 2 cams, one for each side of the trailer.
These cams are designed to work with round or trunnion cam-style bars. This is a simple bolt-on system for A-frame trailers with a frame width that does not exceed 2-1/2 inches. view full answer...
We do have a weld on tab to use with the Reese Friction Sway Bar # 83660, but it isn't included with it.
You will want the Draw-Tite # 3442 it measures 4-7/8 inches long x 1-15/16 inches wide x 7/16 inches deep with a 5/8 inch hole.
I have linked it to this page for your convenience. view full answer...
Yes, the Curt Weight Distribution System, # C17322, comes with everything you will need including the shank and a ball. I have included a link to the installation instructions for you.
You will want to make sure that this is the best system for your needs. Weight distribution systems should be selected based on the tongue weight of the trailer plus the weight of anything loaded behind the rear axle of the towing vehicle.
This system has a tongue weight capacity range of 800 to 1,000... view full answer...
The flat-looking "bars" that come with the Blue Ox Accessory Kit for Tow Bars with 2" Hitch Receivers # BLU64TR are an anti-rattle kit that clamps down on the hitch receiver and shank of your tow bar. This just helps to keep everything from moving around as much as possible.
Just to get a clearer picture of what the kit is, it can be found by itself as the Blue Ox Hitch Receiver Immobilizer # BLU85QR, but the one in the kit is for a 2" hitch instead of a 3" hitch like the one I just referenced. view full answer...
Go To Results